Retatrutide issues

[Omxxl]

Hi there,

I’ve reconstituted two 30mg Reta vials—the ones with this specific label and purple cap—and the solution looks cloudy compared to the 20mg one in the photo. I ordered another 30mg kit in the same shipment; that one had the exact same cap and label, and I didn't have any issues with it.

Has anyone else experienced something similar? The bacteriostatic water is new, and it’s the same water I used to reconstitute my HGH and the other Reta vial.

If it’s cloudy, it’s not safe to inject, right?

Please help.

 

[BNLFL]

Maybe give it a day to clear. I just had that with two R60 from BFF. Next day was perfectly clear.

 

[maokai]

Hospira BAC or vendor? Ideally the peps are higher quality but cause it's not fully controllable, the main thing to keep consistent is your BAC quality so sticking with Hospira.

 

[Lyophilized]

Is your BAC water just made of Benzyl Alc or does it have also Sodium chloride?
Reta with NaCl will crush. With Tirz.. No problem

 

[Flash-BCR]

If the BAC is not Hospira, Check the ph…See if it’s off.

 

[Mochizuki0124]

Just my 2c. I aint pinning anything that is cloudy even if it clears the next day. Most peptides clear within minutes. Grey is already risky, I aint taking additional risk. Its not like we're spending thousands on a single vial.

Best bet is too eliminate the BAC factor and get a hospira and try it out if its cloudy with Hospira too. But then again some kits are hit or miss, You might have 1 kit where 5 reconstitutes fine and 5 thats cloudy even with hospira. I dealt with this with the transparent blue cap R10. Some would recon fine and some would not but I did notice that the chances of it getting cloudy is higher with vendor BAC.

 

[Omxxl]

It’s BAC water from the same source as the peptide itself; I’ve reconstituted other peptides with it and had zero issues. It’s hard to get Hospira here in Europe.

 

[faloppi]

My understanding is if it's cloudy, the the molecules are clumping together. The risk of injecting it goes beyond it being ineffective, there can be immune/allergic/antibody reactions. If it clears up it might be salvageable, but if it gets gel like or has floaties, toss for sure. The nacl is a good catch mentioned above, or possibly the pH of your bac isn't in range. Was the bac water cold when you mixed it? Low temp can make it harder for the powder to mix

 

[Omxxl]

My understanding is if it's cloudy, the the molecules are clumping together. The risk of injecting it goes beyond it being ineffective, there can be immune/allergic/antibody reactions. If it clears up it might be salvageable, but if it gets gel like or has floaties, toss for sure. The nacl is a good catch mentioned above, or possibly the pH of your bac isn't in range. Was the bac water cold when you mixed it? Low temp can make it harder for the powder to mix

Yes, the water was cold, but the second vial wasn't quite as cold.

 

[faloppi]

It’s BAC water from the same source as the peptide itself; I’ve reconstituted other peptides with it and had zero issues. It’s hard to get Hospira here in Europe.

you have cheap pH test strips by chance? if the bac water is a little out of range, it might work for some more forgiving peptides but not be good for the reta (or this batch anyway)

Yes, the water was cold, but the second vial wasn't quite as cold.

if it was just the temp, after 30mins on the counter, and a little swirling, it should clear up

 

[Mochizuki0124]

Yes, the water was cold, but the second vial wasn't quite as cold.

ah.. rule of thumb too, both the BAC and the Peptide should be room temp before recon.