Reta + KLOW? Asking questions, needing answers.

[Such1943]

Can you elaborate on the 2.75mg daily? What does that translate to mL? I calculated 0.1mL per dose. Is this correct?

In a peptide calculator use 2.75 dose, 50mg strength (the amount of GHK-Cu in the mix) and your BAC water. This should calculate the total amount of GHK-Cu per dose. Gave AI the amounts of each compound in the vial and let it do the math.

This is how I did mine:
3 mg of GHK-Cu, 600 mcg of BPC-157, TB-500, & KPV.

 

[MsGizmo]

Yes. 10 units is 0.1mL

 

[MsGizmo]

In a peptide calculator use 2.75 dose, 50mg strength (the amount of GHK-Cu in the mix) and your BAC water. This should calculate the total amount of GHK-Cu per dose. Gave AI the amounts of each compound in the vial and let it do the math.

This is how I did mine:
3 mg of GHK-Cu, 600 mcg of BPC-157, TB-500, & KPV.

My KLOW was premixed, I did not dose for each individual part of it .. I dosed for the entire 80g vial in one go. I am also rather conservative in my dosage amounts. Its a bit of a balancing act ... you want enough to help you heal but not so much to make the injection burn.

 

[Nextlevel]

So my understanding is it is best to get around 1.75mg of copper per shot and most people add 3 ML of BAC to the vial. So wouldn't 0.105ml give you the contents needed?

 

[Twowheelr2]

So my understanding is it is best to get around 1.75mg of copper per shot and most people add 3 ML of BAC to the vial. So wouldn't 0.105ml give you the contents needed?

Peptide Math

1.. 50mg / 3ml=16.667mg/ml
2.. 16.67mg/ml/100units=.167mg per unit
3.. 2.75mg/.167mg/unit=16.467units
With the concentration at 16.667 mg per ml..or 100units it takes 16.467 units to draw 2.75mg .
Is this right? I thought I understood peptide math, but I need to double check my ciphering.

 

[Twowheelr2]

In a peptide calculator use 2.75 dose, 50mg strength (the amount of GHK-Cu in the mix) and your BAC water. This should calculate the total amount of GHK-Cu per dose. Gave AI the amounts of each compound in the vial and let it do the math.

This is how I did mine:
3 mg of GHK-Cu, 600 mcg of BPC-157, TB-500, & KPV.
View attachment 12646

Have you had any reactions at 3mg? I’m doing 2mg daily now..so far it hasn’t been too bad. Much easier than I’ve read about.

 

[Such1943]

I've been calculating for 3m GHK-Cu the whole time. Slight pip every once in a while, nothing major.

 

[Twowheelr2]

I've been calculating for 3m GHK-Cu the whole time. Slight pip every once in a while, nothing major.

I heard so many horror stories I took a bunch of precautions for my first jab. Before my first 2mg dose, I loaded up with zinc and Zyrtec. Split 1st dose into 3 mini pokes, vibe gun. Reconstituted with 3ml BAC. Had very little discomfort. A couple hours after administered the meds, a slight dull pain around the area. Now, no prep, and the last 4 or 5 injections were put into the same area to see if it would produce any extra ISR. so far it’s been fine.

 

[Cdub100]

Can you elaborate on the 2.75mg daily? What does that translate to mL? I calculated 0.1mL per dose. Is this correct?

0.13 to be exact. I take .3 and upwards to .5

 

[Such1943]

I heard so many horror stories I took a bunch of precautions for my first jab. Before my first 2mg dose, I loaded up with zinc and Zyrtec. Split 1st dose into 3 mini pokes, vibe gun. Reconstituted with 3ml BAC. Had very little discomfort. A couple hours after administered the meds, a slight dull pain around the area. Now, no prep, and the last 4 or 5 injections were put into the same area to see if it would produce any extra ISR. so far it’s been fine.

Wednesday I hit something, felt different (SQ). I aborted mission and injected on the other side. I have a nice burse now and some redness. The side I injected into has no pip. Part of the game I suppose. I think it will be there for a few days. It might have been the Mots-C (5mg), just started this week. I'll find out tomorrow when I pin again.